Honeywell BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE 為Issue 3，HKEZIT 提供原廠行貨連保養、上門安裝、調試及使用教學一站式服務。詳細規格以下方原廠 Datasheet 欄位為準，歡迎聯絡我們查詢 BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE 香港價格連安裝報價。
| Mounting | M5 GRADE 8.8 BOLT (X2), recommended mounting torque is 6 Nm ±1 Nm |
|---|---|
| 重量 | 40 g max. |
| 尺寸 | 78,88 mm × 64,13 mm × 17,00 mm |
| Housing material | VALOX DR48 17 % GF |
| Flammability | UL 94 V-0 |
| 防護等級 | IP3X BES Series Datasheet | automation.honeywell.com/hss | 3 64,13 50,00 |
| Figure 1. Product Dimensions | 40,24 17,00 4x 43.6° TABLE 2. PIN OUT |
| Pin | Description 1 Power input 2 Ground 3 CAN H 61,25 4 CAN L 78,88 , NOTE: BES is designed for single use only. It must be replaced after exposure to a thermal event. |
| Pin 2 | Pin 3 |
| Pin 1 | Pin 4 2x 7,925 21,90 |
| BES - 1 | 3 1 -1 1 1 - 001 |
| BES – Electrolyte Vapor | RESERVED FOR FUTURE USE |
| ELECTRICAL POWER | CAN ADDRESS 3 – 0xE6 4 – 0xE7 5 – 0xE8 |
| SEALING | 6 – 0xE9 OUTPUT 1 – CAN 2.0B |
| CONNECTOR | (Baud Rate 250 kbps) (Baud Rate 500 kbps) REDUNDANCY 1 – None BES Series Datasheet | automation.honeywell.com/hss | 4 29-BIT ID DATA (8 BYTES) Scalar |
| Low | High |
| Field | P EDP DP PF PS SA State Deg C Byte Byte Not Used |
| # Bits | 3 1 1 8 8 8 8 8 8 8 8 8 8 8 0x08 0xFF 0x01 0xE4 0x03 0x17 0x1C 0x00 0xFF 0xFF 0xFF 0xFF |
| Message | Description Temperature (C) = (int8_t) * Deg C |
| EDP/DP=0 | J1939 standard data page Value=(int16_t) Scalar/100 |
| PF = 0xEF | Peer-to-peer message Typical warm up -2.00 |
| Destination address | Clean Air 0.00 (address of the controller) |
| Thermal runaway alarm | >1.00 |
| SA = 0xE4 | Source address (address of BES sensor) |
| High level of electrolytes | >4.00 |
| STATE: REPRESENTS THE STATE OF SENSOR | Example |
| Error | 0x01 Scalar (0x001C = 28) |
| Warmup | 0x02 |
| Normal | 0x03 |
| 警報 | 0x04 |
| SENSOR OPERATING MODE | PDU 0xEF00/61184 | ID |
| Frame | ID for operating mode is 29-BIT ID DATA (2 BYTES) ID |
| Format | 0x01 |
| CAN | ECO Mode 0x02 0x19 0xEF 0xE4 0xF6 0x01 0x00 |
| Severity | Protect=0, Warning=1, Stop=2, Malfunction=3 BES Sensor CRC Error (Light=1, Flash = 3, Severity = 1, |
| Light | 0=Off, 1=On, 2=Error, 3=Any DTC=0x7E271, FMI = 0x1F, occurrence = 3) |
| Flash | 0=Slow, 1=Fast, 3=No Flash Example |
| DTC | 0x7E000 - 0x7FFFF refer to fault codes |
| ID | 18FECAE4x most severe=0, 0x1F = not available: ref |
| FMI | Data 04 0C 71 E2 FF 03 FF FF J1939-73 |
| Occurrence | 1-127 BES Series Datasheet | automation.honeywell.com/hss | 5 DM3 (J1939-73 Standard) | PDU 0xFECC / 65228 Frame 29-BIT ID DATA (8 BYTES) Format |
| BES SERIES | ISO 7637-2 |
| Test | Standard Procedure |
| CISPR25 | Section 6.2, Class 3 |
| CISPR 25 Radiated Emissions | CISPR25 Section 6.4, Class 3 |
| Transient Conducted Emission | ISO 7637-2 Section 6.2 |
| Bulk Current Injection (BCI) Test | ISO 11452-4 Frequency range: 1 MHz to 400 MHz, Test Level 200 mA Frequency range: 200 MHz to 1 GHz, Test Level 150 V/m |
| RF Radiated Immunity - ALSE | ISO 11452-2 1 GHz to 6 Ghz, Test Level 100 V/m Frequency range: 10 kHz to 400 MHz, |
| RF Radiated Immunity - Stripline | ISO 11452-5 Test Level: 200 V/m Unpowered direct contact discharge: ±6 kV Unpowered air discharge: ±15 kV |
| Electrostatic Discharge | ISO 10605 Powered-up direct contact discharge: ±8 kV Powered-up air discharge: ±15 kV Network: 330 pF / 330 Ω |
| Long Duration Overvoltage | ISO 16750-2 Section 4.3.1.2 - Jumpstart |
| Transient Overvoltage | ISO 16750-2 Section 4.3.2 |
| Superimposed Alternating Voltage | ISO 16750-2 Section 4.4, Levels 3 and 4 |
| ISO 16750-2 | Section 4.5 |
| Momentary Drop in Supply Voltage | ISO 16750-2 Section 4.6.1 |
| Reset Behavior at Voltage Drop | ISO 16750-2 Section 4.6.2 |
| Reverse Voltage | ISO 16750-2 Section 4.7, Test case 2 |
| Open Circuit | ISO 16750-2 Section 4.9 |
| Short Circuit Protection | ISO 16750-2 Section 4.10.2 |
| Insulation Resistance | ISO 16750-2 Section 4.11 ,10 MΩ at 500 Vdc |
| Low Temperature Operating | ISO 16750-4 Section 5.1.1, TMIN: -40ºC |
| High Temperature Operating | ISO 16750-4 Section 5.1.2, TMAX : 85ºC |
| Thermal Step | ISO 16750-4 Section 5.2, Temp Range: -40 to 85ºC |
| Thermal Cycle | ISO 16750-4 Section 5.3, Temp Range: -40 to 85ºC |
| Humid Heat, Cyclic | ISO 16750-4 Section 5.6, Test 1 and 3 |
| Damp Heat, Steady-State | ISO 16750-4 Section 5.7 |
| Atmospheric Pressure | ISO 16750-4 Section 5.12, -100 m to 5000 m |
| Random Vibration | ISO 16750-3 Section 4.1 Test VII, Commercial Vehicles |
| Mechanical Shock | ISO 16750-3 Section 4.2, Shock Profile II |
| Handling Drop | ISO 16750-3 Section 4.3, 1 m drop |
| Withstand Voltage | ISO 16750-2 Section 4.12, 500 Vrms, 60 Hz for 60 s BES Series Datasheet | automation.honeywell.com/hss | 7 •WARNING |
| Honeywell warrants goods of its | PERSONAL INJURY |
| manufacture as being free of defective | DO NOT USE these products as safety |
| materials and faulty workmanship | or emergency stop devices or in any |
| during the applicable warranty period. | other application where failure of the |
| Honeywell’s standard product warranty | product could result in personal injury. |
| applies unless agreed to otherwise by | Failure to comply with these Honeywell in writing; please refer to your instructions could result in death or |
| order acknowledgment or consult your | serious injury. local sales office for specific warranty details. If warranted goods are returned |
| to Honeywell during the period of | •WARNING coverage, Honeywell will repair or replace, MISUSE OF |
| at its option, without charge those items | DOCUMENTATION |
| that Honeywell, in its sole discretion, | • The information presented in this |
| finds defective. The foregoing is buyer’s | product sheet is for reference only. |
| sole remedy and is in lieu of all other | Do not use this document as a |
| warranties, expressed or implied, | product installation guide. |
| including those of merchantability | • Complete installation, operation, and maintenance information and fitness for a particular purpose. is provided in the instructions In no event shall Honeywell be liable supplied with each product. for consequential, special, or indirect Failure to comply with these damages. instructions could result in death or |
| While Honeywell may provide information | serious injury. or engineering support for its products through Honeywell personnel, literature and website, it is the buyer’s sole responsibility to determine the suitability of the Honeywell product(s) for the buyer’s requirements. Specifications may change without notice. The information we supply is believed to be accurate as of this writing. However, Honeywell assumes no |
| For more information | responsibility for its use. |
| USA/Canada | +302 613 4491 |
| Latin America | +1 305 805 8188 |
| Europe | +44 1344 238258 |
| Japan | +81 (0) 3-6730-7152 |
| Singapore | +65 6355 2828 |
| Greater China | +86 4006396841 006023-3-EN | 3 | 01/26 |
| www.honeywell.com | © 2026 Honeywell International Inc. All rights reserved. |
* 規格以原廠最新 Datasheet 為準。
下載完整PDF規格書 →
78,88 mm × 64,13 mm × 17,00 mm｜重量 40 g max.｜Unit: mm
BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE Honeywell Issue 3亦適合以下專業服務機構使用，保安同合規要求同一般商鋪唔一樣，歡迎查詢度身方案。
HKEZIT 提供原廠行貨連保養，BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE 原廠行貨連保養，提供上門評估、安裝、防區設定及使用教學一站式服務，全港 32 區均有服務。
詳細規格請參閱上方規格表；我們會按現場環境（商舖、辦公室、倉庫、住宅）設計防區及感應器布局，並提供整體方案報價。
可按需求配置本地警號、手機 App 推送或短訊通知；亦可與 CCTV 聯動，觸發時自動錄影存證。
兩者屬同系列產品，實際應該邊個型號更適合，需視乎現場環境同需求而定。歡迎直接聯絡我們免費現場評估，由工程師建議最合適方案。
HKEZIT 提供 BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE 原廠行貨連保養，安裝後如有故障可直接聯絡我們安排上門維修，毋須自行聯絡原廠。詳情請參閱防盜報警安裝工程頁面或聯絡我們查詢保養範圍。
HKEZIT 於全港各區提供 BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE Honeywell Issue 3供貨連專業安裝服務（裝ALARM、裝防盜、裝警鐘），熱門地區包括：藍田防盜報警系統安裝、觀塘防盜報警系統安裝、銅鑼灣防盜報警系統安裝、鑽石山防盜報警系統安裝、長沙灣防盜報警系統安裝、青衣防盜報警系統安裝、香港仔防盜報警系統安裝、黃大仙防盜報警系統安裝。港島、九龍、新界全港 32 區均有上門安裝，歡迎聯絡我們查詢 BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE 香港價格連安裝報價。
BES-SERIES-BATTERY-SAFETY-ELECTROLYTE-SE Honeywell Issue 3適合多種場景使用，以下為部分常見安裝場景，歡迎查詢是否適合您的現場環境。
企業秘書、稅務顧問公司裝防盜系統，客戶公司機密檔案室紅外線探測、門磁窗磁全面佈防，非辦公時段自動戒備配警鐘聯動保安公司，24小時中央監控站接報即時通知，誤觸發率低確保稅季運作暢順。免費上門評估，灣仔、上環顧問公司即約報價。
WhatsApp 查詢 →建築工程顧問公司裝防盜系統，圖則模型檔案室紅外線探測、門磁窗磁全面佈防，非辦公時段自動戒備配緊急按鈕聯動保安公司，24小時中央監控站接報，誤觸發率低防止項目資料外洩。免費上門評估，觀塘、九龍灣工廈辦公室即約報價。
WhatsApp 查詢 →知識產權、專利代理公司裝防盜系統，未公開專利同商業機密文件室紅外線探測、門磁窗磁全面佈防，非辦公時段自動戒備配警鐘聯動保安公司，24小時中央監控站接報即時通知，誤觸發率低防止資料外洩爭議。持牌團隊免費勘察，中環、觀塘專業樓層即約報價。
WhatsApp 查詢 →牙科診所裝防盜系統，X光室紅外線探測、門磁窗磁全面佈防，非診症時段自動戒備配警鐘聯動保安公司，24小時中央監控站接報即時通知，誤觸發率低不影響日常應診。免費上門評估，銅鑼灣、尖沙咀專科醫務中心即約報價。
WhatsApp 查詢 →骨科診所裝防盜系統，復康儀器房紅外線探測、門磁窗磁全面佈防，非診症時段自動戒備配警鐘聯動保安公司，24小時中央監控站接報即時通知，誤觸發率低不影響日常應診。免費上門評估，銅鑼灣、尖沙咀專科醫務中心即約報價。
WhatsApp 查詢 →耳鼻喉科診所裝防盜系統，內窺鏡儀器室紅外線探測、門磁窗磁全面佈防，非診症時段自動戒備配警鐘聯動保安公司，24小時中央監控站接報即時通知，誤觸發率低不影響日常應診。免費上門評估，銅鑼灣、尖沙咀專科醫務中心即約報價。
WhatsApp 查詢 →查看更多防盜報警適用場景，請參閱 防盜報警安裝工程。
如需整套防盜報警方案，請參閱 防盜報警安裝工程。