HONEYWELL CS-2508 防盜報警安裝・保養

Name: HONEYWELL CS-2508 • Three (411) or four (411UD) monitoring
Brand: honeywell
SKU: CS-2508

產品簡介

honeywell CS-2508 為• Three (411) or four (411UD) monitoring，HKEZIT 提供原廠行貨連保養、上門安裝、調試及使用教學一站式服務。詳細規格以下方原廠 Datasheet 欄位為準，歡迎聯絡我們查詢 CS-2508 香港價格連安裝報價。

Channels/Inputs:**：FCC Registration: OAAUSA-25431-AL-E. • J4 Jumper installed:
• Programmable Channels 1 through 4.：Ringer Equivalence: 0.5 B. and power-limited 12 VDC (nominal
For Canadian Applications:：must be supplied at TB1 Terminals 1(+) and
• Power-limited circuitry.：2(–). Operating voltage must be within 11.2 IC Certificate N
• Fully supervised.：Ringer Equivalence Number (REN): 0.2. to 12.4 VDC (UL tested

HKEZIT 提供原廠行貨保養。硬件連專業安裝、設定及使用教學一站式報價，無需自行研究安裝與設定。我們同時承接裝ALARM、裝防盜、裝警鐘工程，硬件與工程同一團隊負責。

查詢價格連安裝 →

CS-2508 honeywell • Three (411) or four (411UD) monitoring 產品圖片

詳細規格

Channels/Inputs:**	FCC Registration: OAAUSA-25431-AL-E. • J4 Jumper installed: Filtered, nonresettable,
• Programmable Channels 1 through 4.	Ringer Equivalence: 0.5 B. and power-limited 12 VDC (nominal) power
For Canadian Applications:	must be supplied at TB1 Terminals 1(+) and
• Power-limited circuitry.	2(–). Operating voltage must be within 11.2 IC Certificate Number: 2132 9028 A.
• Fully supervised.	Ringer Equivalence Number (REN): 0.2. to 12.4 VDC (UL tested range: –15%, +10%). Current requirements are 78 mA in standby B). Requires Normally Open contact to trigger. a keypad, model PRO-411, is available for
programming the 411 Series.	*NOTE: A maximum of 240 mA is possible
• Normal operating voltage: 12 VDC.	with all input channels active, the 411
• Alarm current: 3.34 mA.	Operating Power: The 411 may be powered communicating, the Programmer connected,
from UL-listed control panels that output	and Lamp Test active.
• End-of-line resistor: 2.2K ohms.	nonresettable and power-limited 12 or 24
input.	determines whether 12 VDC power is to be TB2 Terminals 1 through 6:
**NOTE: Channels/inputs do NOT support	supplied directly to the 411 circuit board, or • Programmable Channels 1 through 3.
two-wire smoke detectors.	24 VDC power is to be supplied and then • Power-limited circuitry.
internally regulated down to 12 VDC.	• Fully supervised.
DC Power: TB1 Terminals 1(+) and 2(–);	• Operation: All channels NFPA Style B (Class
• Contact rating: 2.0 amps @ 30 VDC	Terminal 3 is Earth Ground. B). Requires Normally Open contact to trigger. (resistive).
• J4 Jumper removed: nonresettable, and	• Normal operating voltage: 12 VDC.
power-limited 24 VDC (nominal) power must	• Maximum line resistance: 100 ohms per be supplied at TB1 Terminals 1(+) and 2(–). channel.
Operating voltage provided must be within	• Alarm current: 3.34 mA. 21.3 to 24.0 VDC (UL tested range: –15%,
+10%). Current requirements are 78 mA in	• End-of-line resistor: 2.2K ohms, 1/2 watt (P/N
standby and 126 mA* while communicating.	27070). • Short circuit current: 3.8 mA per channel/ input. **NOTE: Channels/inputs do NOT support two-wire smoke detectors. Gamewell-FCI 12 Clintonville Road Northford, CT 06472-1610 Phone: 203-484-7161 Specifications and wiring information are provided for information only and are Fax: 203-484-7118 believed to be accurate. Gamewell-FCI assumes no responsibility for their use.
www.gamewell-fci.com	Data and design are subject to change without notice. Installation and wiring instructions shipped with the product shall always be used for actual installation.
A Honeywell Company	For more information, contact Gamewell-FCI. © 2009 Gamewell-FCI
Page 4 of 4	411/411UD CS-2508 A