| TYPICAL APPLICATIONS | (with optional ECC-50W-25/70V and ECC-CE6 installed) |
|---|
| • | Schools • Healthcare Facilities • Factories • 520Hz square wave tones available, which can be uploaded to the ECC-50/100 to meet NFPA Low Frequency requirements |
|---|
| DF-60760. | PUSH BUTTON CONTROLS – Optional ECC-RPU Remote Page Unit (includes cabinet) See • All Call • Message Select 1-14 DF-60761. |
|---|
| • MNS Control | • Diagnostic Select – Optional ECC-LOC Local operator console (includes cabinet) |
|---|
| See DF-60762. | • System Control • Trouble Silence – Optional ECC-50DA(E) distributed amplifier, 50 watts. See DF- 60763. LED Status Indicators (visible with door – Optional ECC-125DA(E) distributed amplifier, 125 watts. See closed) DF-60763. – Optional ECC-50BDA distributed amplifier with backup, 100 • Fire System Active (green) • LOC/RPU/RM 1-8 Active (green) watts.See DF-60760. |
|---|
| • MNS Control (green) | • Main Console Fault (yellow) |
|---|
| Optional Internal Expansion Modules | • System Control (green) • AC Power (green) |
|---|
| • System in Use (green) | • Ground Fault (yellow) |
|---|
| • Speaker Zone 1-24 Fault (yellow) | • Battery Fault (yellow) |
|---|
| • OK to Page (green) | • Data Bus Fault (yellow) • Remote Amplifier 1-8 Fault (yellow) • Audio Riser Fault (yellow) |
|---|
| metal brackets. | LED Indicators (visible with door and dress panel open) • Speaker Volume Control Fault (yellow) • Option Card Fault (yellow) • Amplifier Over Current Fault (yellow) |
|---|
| -25/70V | optional |
|---|
| Internal options | amplifier -CE6 circuit expander |
|---|
| NAC Circuit | Speaker Circuits |
|---|
| TB19 | TB20 & TB21 -FFT firefighter telephone |
|---|
| remote | -LOC local -RPU remote |
|---|
| operator console | -RM remote |
|---|
| consoles | paging unit microphone TB4 TB12 |
|---|
| charger - J7 | TB22 distributed audio |
|---|
| -50DA 50W remote | -125DA 125W remote -50BDA 50W remote |
|---|
| amplifier | amplifier amplifier |
|---|
| CHG-120 charger | CHG-75 charger DF-60734:B1 • 8/15/2018— Page 3 of 6 |
|---|
| Product Line Information | CHG-75: 25 to 75 ampere-hours (AH) External Battery Charger. BAT-1270: Battery,12 volt,7.0 AH (Two required). |
|---|
| tion. | tem) |
|---|
| DF-60763 for more information. | • Maximum battery charge capability: 2.8 Amps, 26AH (ECC cabi- net holds max. 18AH battery). |
|---|
| sheet DF-60765 for more information. | • 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive). |
|---|
| FPJ-F: Remote Phone Jack. | NOTIFICATION APPLIANCE CIRCUIT (NAC) OUTPUT RAT- ING (TB19) |
|---|
| MMF-301: Addressable Mini-Monitor Module. | • Maximum signaling current for special application power: 2.0A. |
|---|
| I300: SLC Line Isolation Module. | • Maximum signaling current for regulated power: 200mA. |
|---|
| TR-CE: Optional Trim Ring. | • Maximum wiring impedance: 1Ω. |
|---|
| Style Y (Class B) operation. | sure only. |
|---|
| patible devices. | • Normal Operating Voltage Range: 10.5 VDC - 29 VDC; (Maxi- |
|---|
| NAC FOLLOWER OUTPUT REMOTE SYNC (TB18) | mum Voltage: 29 VDC). |
|---|
| SPEAKER CIRCUITS | • Non-resettable power for external operator interface components. |
|---|
| • Primary Speaker Circuit (TB20) | • Power-limited circuitry, non-supervised. – Circuit can be wired Style Y (Class B) or Style Z (Class A). • Maximum output current: 0.80 amps. |
|---|
| – Power-limited circuitry. | • Current limit: fuse-less, electronic, power-limited circuit. – Normal Operating Voltage: 25 VRMS @ 2 amps max and maxi- mum Load Impedance of 12.5Ω (70.7 VRMS @ 700 mA max. EXTERNAL DATA BUS (EIA-485) (TB12) with maximum load Impedance of 100Ω operation possible by • Data connections for external operator interface components. plugging optional ECC-XRM-70V conversion transformer into • Redundant |
|---|
| J12 of the main control board). | • Power-limited circuitry, supervised. – Output Power: 50 watts (10 watts when background music is • Maximum wiring impedance: 13.2Ω employed). |
|---|
| – Frequency Range: 400Hz - 4,000Hz. | FACP DATA BUS (EIA-485) (TB13) – Maximum total capacitance for each speaker circuit: 250 µF. • Dedicated connection to FACP serial bus. – End-of-Line Resistor required for Style Y circuit: 15 KΩ, 1 watt • Output terminals: pass-through to other system components. (P/N: ELR-15K). • Isolated, supervised. |
|---|
| NAC circuits to NAC devices down stream. | • Style Y (Class B) or Style Z (Class A) audio connections to exter- |
|---|
| NAC circuits to NAC devices downstream. | • Audio signal level: 3.85 V, maximum. |
|---|
| sure only. | • Frequency range (ECC-50/125DA): 800Hz - 2KHz RMS. DF-60734:B1 • 8/15/2018— Page 5 of 6 |
|---|
| Electrical Specifications Display Board | Cabinet Specifications |
|---|
| EXTERNAL AUDIO INPUT (TB5) | • Backbox: 19.0"(48.26 cm) high x 16.65"(42.29 cm) wide x 5.20"(13.23 cm) deep. • Door: 19.26” (48.92 cm) high x 16.82”(42.73 cm) wide x |
|---|
| • Input Voltage: 700 mV rms maximum | 0.12”(0.30 cm) deep. |
|---|
| • Input Current: 0.1 mA maximum @ 700 mV | • Trim Ring (TR-CE): 22.00” (55.88 cm) high x 19.65” (49.91 cm) Shipping Specifications |
|---|
| ECC-CE6 Circuit Expander Module Specifi- | Base Unit Weight: 27.85 lbs (12.63 kg). Temperature and Humidity ranges (Class B) or Style Z (Class A). – 120°F and at a relative humidity 93% ± 2% RH (noncondensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's amps max. (Maximum Load Impedance of 12.5Ω). affected by extreme temperature ranges and humidity. Therefore, it 100Ω operation possible for the primary circuit by p |
|---|
| music, and alarm. | The listings and approvals below apply to the basic ECC-50/100(E) control panel. In some cases, certain modules may not be listed by 4,000Hz. tory for latest listing status. |
|---|
| vides programmed speaker control. | Standards and Codes The ECC-50/100(E) complies with the following UL Standards, NFPA 72, International Building Codes, and California Building Codes. |
|---|
