honeywell HBT-BMS-MCM34 為CONTROLLER，HKEZIT 提供原廠行貨連保養、上門安裝、調試及使用教學一站式服務。詳細規格以下方原廠 Datasheet 欄位為準，歡迎聯絡我們查詢 HBT-BMS-MCM34 香港價格連安裝報價。
| PART NUMBER | DESCRIPTION |
|---|---|
| ENVIRONMENT | 201-930 MCM34 Finished assembly |
| SPECIFICATION | RANGE/VALUE APPROVALS |
| Operating Temperature Range | 0 - 40 °C APPROVALS |
| Operating Humidity Range | 0 - 95 % RH FCC PART 15B, CE-LVD, CE-EMC and CB |
| PARAMETER | SPECIFICATION |
| Operating supply Voltage | 12 ± 0.25 VDC |
| Current Consumption | 15mA to *35mA |
| NVRAM Capacity | 256 Bytes |
| Program Code Capacity Volatile RAM | 32 kBytes |
| Max. Injected Input Current IO1-IO5 | 3 mA, 0-5 VDC Pull-up Resistor IO1- IO5 Input voltage range IO1-IO5 10 kOhm |
| Max. Injected Input Current InOut 1-2 | 15 mA, 0-5 VDC Pull-up Resistor InOut 1-2 Input Voltage Range 1.5 kOhm |
| • | The MCM34 FLN5 RS-485 configuration can ONLY be used with a B573 or B576-L Floor Bridge that uses RS-485 FLN5 protocol. It can NOT be used with a B576-S floor bridge which uses the enhanced DM485 RS-485 protocol. |
| HEADER | PIN SIGNAL FUNCTION NOTES WIRE COLOR 1 Gnd Common NA |
| H1 -Analog Out 1,2 | 2 AO1 Analog Out 1 NA Driver_index_10V_DC-Pin Index 0 3 AO2 Analog Out 2 Driver_index_10V_DC-Pin Index 1 1 Gnd Common Connect a 01-9489 B485 module to H2 using 5 pin 2 VEE+12V 12 VDC |
| H2-In/Out 1,2 | 62-1514-A.3 cable. Registry |
| connection that uses 01- | bus set to 0 in the MCM34. 4 InOut1 UArt Tx 5 InOut2 UArt Rx 1 Gnd Common Brown 2 VEE+12V 12VDC Red 3 S5 bus Mult-drop communication Orange bus 4 Out1 Open -Collector Yellow Driver_Index_Relay-Pin Index 0 Output 5 In2 0-3.3 DC Dry Contact Green Driver_Index_LV_DC- Pin Index 5 |
| Input | In6 pulled up to 3.3V via 10K resistor 1 Gnd Common NA NA |
| H4 Analog In 1,2 | 2 AI1 Analog In 1 Driver_index_10V_DC-Pin Index 0 3 AI2 Analog In 2 Driver_index_10V_DC-Pin Index 1 1 Gnd 12 VDC Brown 2 VEE + 12 V I/O Red IO1-IO5 are general purpose Inputs/Outputs and are internally 3 IO1 I/O Orange pulled up to 3.3 VDC via 10K resis- |
| H5- I/O 1 to 5 | 4 IO2 I/O Yellow tor. Tyical use is for Dry contact 5 IO3 I/O Green inputs or low voltage outputs to 6 IO4 I/O Blue control a connected LED indicator 7 IO5 I/O Violet 1 Gnd 2 3.3VDC 3 SCI_Tx 4 SCI_Rx Connect ST-Link V2 STM32 programmer to reprogram |
| Programming Header | 5 NRST MCM34 6 SWO 7 SWCLK 8 SWDIO 1 Gnd Common Brown 2 3.3 VDC 3.3VDC Red Connect 203-250 RS 485 adapter |
| H7 -Alternate RS-485 | 3 RS485 Tx RS485 Tx Orange to H7 if using alternate RS-485 |
| FLN5 connection if using | FLN5 connection. Registry |
| Part# 203-250 adapter | 4 RS485 Rx RS485 Rx Yellow 193:11:0:0 SerialPort must be set 5 TXE TXE Green to 1 in the MCM34 6 Not Used Blue 1 Gnd Common Brown 2 12VEE+12 V 12VDC Red 3 S5 Bus Mult-drop communication Orange bus INCOMM MCM34 Product Data Sheet | www.honeywell.com | 8 |
| LED BEHAVIOUR | DESCRIPTION |
| Off | MCM34 is not powered On for 1 second, Off for 1 second and repeat- The MCM34 is powered but is NOT connected to a B573 or B576-L Floor Bridge and has |
| ing | not received a “Central Status Broadcast” from the Room Gateway so it does not think the room is online/connected to the Inncom server. |
| A blink once per second and repeating | The MCM34 is powered and has received a “Central Status Broadcast” from the Room Gate- way so it thinks the room is online/connected to the Inncom server. 3 blinks every 2 seconds The MCM34 is connected to a B573 or B576-L Floor bridge and receiving FLN5 data, but it has has not received a “Central Status Broadcast” from the Inncom server so it does not think the room is online/connected to the In |
| Steady Rapid Blink (3 blinks per second) | The MCM34 has received an Address or I/O Map teach command. Press the SW1 button on the MCM34 to accept the teach command. Eight blinks 1/2 seconds apart, followed by a The MCM34 was just taught and accepted an Address or I/O Map and then Reset. very rapid blink for 4 seconds On for 1 second , followed by a very rapid blink The MCM34 just had power applied or was Reset , or the SW1 switch was pres |
| for 4 seconds | MCM34 sent a reverse bind command but never received a Bind/Configuration offer. SW1 is used for teaching the MCM34 a specific Address or function map. Using the INNCOM thermostat service mode or PC configuration tool, send a “Device Address Teach” or “IOMap Teach” command to the MCM34. Observe the MCM34 Diag LED change to a Fast Blink pattern (3 blinks per second), indicating it is ready to accep |
* 規格以原廠最新 Datasheet 為準。
下載完整PDF規格書 →HBT-BMS-MCM34 honeywell CONTROLLER亦適合以下專業服務機構使用，保安同合規要求同一般商鋪唔一樣，歡迎查詢度身方案。
HKEZIT 提供原廠行貨連保養，HBT-BMS-MCM34 原廠行貨連保養，提供上門評估、安裝、防區設定及使用教學一站式服務，全港 32 區均有服務。
詳細規格請參閱上方規格表；我們會按現場環境（商舖、辦公室、倉庫、住宅）設計防區及感應器布局，並提供整體方案報價。
可按需求配置本地警號、手機 App 推送或短訊通知；亦可與 CCTV 聯動，觸發時自動錄影存證。
兩者屬同系列產品，實際應該邊個型號更適合，需視乎現場環境同需求而定。歡迎直接聯絡我們免費現場評估，由工程師建議最合適方案。
HKEZIT 提供 HBT-BMS-MCM34 原廠行貨連保養，安裝後如有故障可直接聯絡我們安排上門維修，毋須自行聯絡原廠。詳情請參閱防盜報警安裝工程頁面或聯絡我們查詢保養範圍。
HKEZIT 於全港各區提供 HBT-BMS-MCM34 honeywell CONTROLLER供貨連專業安裝服務（裝ALARM、裝防盜、裝警鐘），熱門地區包括：大圍防盜報警系統安裝、大埔防盜報警系統安裝、大角咀防盜報警系統安裝、將軍澳防盜報警系統安裝、尖沙咀防盜報警系統安裝、屯門防盜報警系統安裝、旺角防盜報警系統安裝、柴灣防盜報警系統安裝。港島、九龍、新界全港 32 區均有上門安裝，歡迎聯絡我們查詢 HBT-BMS-MCM34 香港價格連安裝報價。
HBT-BMS-MCM34 honeywell CONTROLLER適合多種場景使用，以下為部分常見安裝場景，歡迎查詢是否適合您的現場環境。
商鋪裝防盜系統，捲閘震動感應、門磁窗磁、紅外幕簾防爆竊，收銀緊急按鈕連警鐘聯動保安公司，24小時中央監控站接報，誤觸發率低唔怕熄燈後保安巡邏誤觸。免費上門評估、明碼實價報價，旺角、觀塘等旺區商舖即約勘察。
WhatsApp 查詢 →村屋、獨立屋裝防盜系統，圍欄周界紅外對射、門窗磁感全面佈防，手機App遠程佈防撤防，警鐘聯動保安公司同24小時中央監控站，誤觸發率低適合寵物出入唔會亂響。專業團隊免費上門評估，元朗、屯門村屋一帶即約勘察。
WhatsApp 查詢 →辦公室、寫字樓裝防盜系統，紅外幕簾入侵偵測、門窗門磁全面佈防，下班定時自動戒備配警鐘聯動保安公司，24小時中央監控站接報，誤觸發率低唔怕清潔阿姐夜間出入。免費上門評估、明碼報價，中環、觀塘寫字樓即約勘察。
WhatsApp 查詢 →貨倉、物流中心裝防盜系統，周界紅外對射、貨櫃門磁感應、分區佈防戒備，警鐘鳴響聯動保安公司同24小時中央監控站接報，誤觸發率低適合大範圍存倉環境。免費上門度尺、明碼報價，葵青、荃灣貨倉即約勘察。
WhatsApp 查詢 →珠寶店、金行裝防盜系統，展櫃夾萬震動感應、紅外幕簾防破窗、腳踏緊急按鈕直通保安公司，24小時中央監控站聯防，誤觸發率低適合繁忙客流出入頻密。持牌團隊免費上門評估，旺角、深水埗珠寶金行即約勘察。
WhatsApp 查詢 →住宅、屋苑單位裝防盜系統，玄關窗花紅外探測、門磁感應全面佈防，手機App遠程佈防撤防即時通知，警鐘聯動保安公司同24小時中央監控站，誤觸發率低唔驚動鄰居。免費上門評估、明碼報價，沙田、屯門屋苑住戶即約勘察。
WhatsApp 查詢 →查看更多防盜報警適用場景，請參閱 防盜報警安裝工程。
如需整套防盜報警方案，請參閱 防盜報警安裝工程。