| • Saves the cost of two | • Operates over the • Works over any type of Private Static IP • QOS: Quality of Service |
|---|
| dedicated phone lines. | following customer provided addressing. diagnostics via |
|---|
| communication | Ethernet 10/100 based AlarmNet conveys vital |
|---|
| • Single or dual path | protocols: HSPA+ (4G) network connection • Built-In Power Supply communicator |
|---|
| communications- (can | HSPA (HSDPA & (LAN or WAN), DSL module: On board information including |
|---|
| communicate to | HSUPA) (3G), EDGE modem or cable charging circuit design when message was |
|---|
| central station using | (2G GPRS) (2G). modem. accommodates back- received, signal |
|---|
| cellular technology, | up battery. Includes strength, and message |
|---|
| internet, or both. | • Selectable reporting • Data transmits over primary power and path used. |
|---|
| paths and supervision | standard contact-ID battery supervision. |
|---|
| • Requires no change to | intervals to meet NFPA protocol but is secured • 7720P Hand-held |
|---|
| the existing Fire Alarm | 72, chapter 26 with the industry's • Diagnostic LEDs: programmer for easy |
|---|
| Control Panel | requirements. advanced encryption Signal strength and setup. |
|---|
| configuration. | (Compliant with NFPA standard (AES 256 bit). status indicators. (Connects directly to 72 2010 and 2013 |
|---|
| the primary and | supervision • Supports both dynamic • Reliable connection: IP |
|---|
| secondary telephone | requirements.) (DHCP) or Public and and GSM connection |
|---|
| ports of a DACT.) | tested every day. • Primary Central Station ID (two digits) obtained from your monitoring station. All of these parameters are assigned by the monitoring station. |
|---|
| paths and supervision timing intervals.) | Note: Some assembly is required. See Installation and Setup Guide #800-12454 for full details. |
|---|
| Selectable Path | Description Supervision |
|---|
| Times | Fire Communicator Capability AlarmNet Honeywell's AlarmNet has been the nationwide leader reliable alternative for the transmission of alarm |
|---|
| Operation | signals, our radio network provides extensive coverage standards 70 and 72. • IPGSM-4G must be mounted in the same room and shall be listed, must be powered from an un- switched branch circuit, and be provided with appropriate standby power. • IPGSM-4G must use the 7AH battery (not supplied) to provide 24-hour backup capability. |
|---|
| ELECTRICAL | PRODUCT LINE INFORMATION Ademco® and AlarmNet® are registered trademarks of |
|---|
| Transformer: | IPGSM-4G: Internet and Digital Cellular Fire Alarm Honeywell International Inc. |
|---|
| Primary: 120VAC, 60Hz, 0.5A | Communicator Panel. Includes red cabinet with Ademco® key and lock, wall outlet box, Dialer Capture Module, IGSM This document is not intended |
|---|
| Secondary: 18VDC, 50VA | to be used for installation Communications Module, antenna & mounting adapter, |
|---|
| 電池 | purposes. We try to keep our PowerBoost1 power supply, LED display board, One 12 V 7.0 AH lead-acid battery: (not supplied) product information up-to- transformer, manual, & required screws, cables, etc. date and accurate. We cannot |
|---|
| Battery charging current: 1 Amp maximum | Antenna External Hardware cover all specific applications Battery discharge current: Standby 230mA, Active GSM-ANT3DB: 3db gain external/remote antenna or anticipate all requirements. 950mA All specifications are subject to WA7626-CA: SNA to N Adapter change without notice. |
|---|
| CABINET SPECIFICATIONS | 7626-50HC: 50 ft. antenna cable, low loss Dimensions: 14.875" H x 12.75" W x 3.0" D (37.8 cm H 7626-25HC: 25 ft. antenna cable, low loss |
|---|
| x 32.4 cm W x 7.6 cm D) | Note: The GSM-ANT3DB and the WA7626-CA are both required for |
|---|
| Color: Red | installing an external antenna along with the necessary cable needed (7626-50HC: 50 ft. or 7626-25HC: 25 ft.) Other Accessories Weight: 5.3 lbs. (6.94 kg) 7720P: IPGSM-4G hand held programmer. Dimensions: 15.625" H x 13.79" W x 9.25" D (39.7 cm H |
|---|
| x 34.9 cm W x 23.9 cm D) | HPTCOVER: Plug-in transformer box for IPGSM communicator. BAT-1270: Battery 12 Volts, 7 AH, sealed. CSFM: 7300-1645:0199 FDNY: COA #6219 DH-60769 | F | 06/17 |
|---|
| www.honeywell.com | ©2017 Honeywell International Inc. |
|---|
