CAMBIUM 60GHZ 網絡設備安裝・保養

Name: CAMBIUM 60GHZ 60 GHZ cnWave™
Brand: Cambium
SKU: 60GHZ

產品簡介

Cambium 60GHZ 為60 GHZ cnWave™，HKEZIT 提供原廠行貨連保養、上門安裝、調試及使用教學一站式服務。詳細規格以下方原廠 Datasheet 欄位為準，歡迎聯絡我們查詢 60GHZ 香港價格連安裝報價。

V5000 Distribution Node：IEEE 802.3af/at, 25 W maximum
System Hardware：43
l：Distribution Node (DN) - DN connects with other DN for mesh
Cambium description：Radio node Cambium part number
Outdoor AC/DC PSU, 100W, 54V DC：V3000, V5000 N000000L179B

HKEZIT 提供原廠行貨保養。硬件連專業安裝、設定及使用教學一站式報價，無需自行研究安裝與設定。我們同時承接裝WIFI、裝ROUTER、裝FIREWALL工程，硬件與工程同一團隊負責。

查詢價格連安裝 →

詳細規格

V5000 Distribution Node	IEEE 802.3af/at, 25 W maximum
System Hardware	43
l	Distribution Node (DN) - DN connects with other DN for mesh network
Cambium description	Radio node Cambium part number
Outdoor AC/DC PSU, 100W, 54V DC	V3000, V5000 N000000L179B
Waterproof PSU Cable Joiner 14-16 AWG	V3000, V5000 N000000L180A
DC to RJ45 Plug Power Adaptor	V3000, V5000 C000000L184A
Cable Gland, Long, M25, Qty 5	V3000, V5000 C000000L124A
AC power Injector 56V, 60W	V3000, V5000 N000065L001C V5000
CABLE, UL POWER SUPPLY CORD SET, INDIA	V1000, V3000, N000900L012A V5000 V5000
CABLE, UL POWER SUPPLY CORD SET, CHINA	V1000, V3000, N000900L015A V5000 V5000 V5000 V5000 V5000 V5000
Category	Specification
尺寸	118 mm (4.64 in) x 43 mm (1.69 in) x 32.4 mm (1.27 in)
重量	0.18 Kg (0.39 lbs)
Temperature	0°C (32°F) to +50°C (140°F)
Humidity	10% to 95 % non-condensing
AC Input	90-264V AC, 47-63 Hz
DC Output Voltage	56V
DC Output current	0.25A
Efficiency	Better than 84% at full load
Over Current Protection	Hiccup mode, recovers automatically after the fault condition is removed
Hold up time	At least 10 milliseconds
RJ45 POE Port	7,8 ------------- DC V- 5,6 ------------- DC V+ Note The Gigabit power injector is supplied with the cnWave V1000 CN. Order part N000900L017A to obtain spares. Warning Always use an appropriately rated and approved AC supply cord-set in accordance with the regulations of the country of use.
DC Output voltage	56V
Part number and	N000000L178A (60W) 171 mm (6.7 in) x 62 mm (2.4 in) x 37 mm
N000000L179A(100W)	220 mm (8.7 in) x 68 mm (2.7 in) x 39 mm (1.5 in)
供電	60W 100W
Waterproofing	IP65/IP67
Power factor	Better than 0.95 Figure 33: Cable joiner Figure 34: DC to RJ45 plug power adapter
Radio	PoE enabled Maximum cable length
V3000	- 390m 25W 72m
V5000	- 330m 25W Not supported
CAT6A outdoor cable, 305m	N000082L172B
RJ45 connector for CAT6A cable	N000082L174B
CAT6A outdoor cable, 100m	N000000L155A
Cable gland for 4-6mm cable, M25, Qty 10	C000000L176A
Cable gland for 6-9mm cable, M25, Qty 10	C000000L123A
CAT5E Outdoor Cable, 100m drum	N000082L016A
Cable gland Long, M25, Qty 5	C000000L124A
DC to RJ45 plug power adapter	C000000L184A Note One cable gland for 6-9mm cable size is included with each cnWave radio. Order additional cable glands as spares, where smaller cable size is to be used, or where the V3000 or V5000 Aux port is to be used.
Optical CABLE,MM, 1m	N000082L215A
Optical CABLE,MM, 2.2m	N000082L191A
Optical CABLE,MM, 10m	N000082L192A
Optical CABLE,MM, 20m	N000082L193A
Optical CABLE,MM, 30m	N000082L194A
Optical CABLE,MM, 50m	N000082L195A
Optical CABLE,MM, 80m	N000082L196A
Optical CABLE,MM, 100m	N000082L197A
Optical CABLE,MM, 150m	N000082L198A
Optical CABLE,MM, 200m	N000082L199A
Optical CABLE,MM, 300m	N000082L200A
Optical CABLE,SM, 2.2m	N000082L186A
Optical CABLE,SM, 10m	N000082L187A
Optical CABLE,SM, 20m	N000082L188A
Optical CABLE,SM, 30m	N000082L139A
Optical CABLE,SM, 50m	N000082L140A
Optical CABLE,SM, 80m	N000082L141A
Optical CABLE,SM, 100m	N000082L142A
Optical CABLE,SM, 150m	N000082L143A
Optical CABLE,SM, 200m	N000082L189A
Optical CABLE,SM, 300m	N000082L190A
System Planning	56 Never mount equipment in Zone A. Mounting in Zone A may put equipment, structures and life at risk.
Type of ODU	Max surface area (square meters) Wind speed (km/h Newtons) 200* 225 250 275 300 325
V1000	0.017544 67 85 105 127 151 177
v3000**	0.1764 462 583 719 871 1036 1216
Item	Specification
Channel	Open/R protocol or manual selection selection
Manual power	Supports ATPC automatic transmit power control and maximum EIRP can be set
control	lower than the default power limit.
Integrated	l V3000 44.5 dBi gain and 40.5 dBi gain antenna type
Duplex schemes	Symmetric 50:50 fixed and asymmetric fixed
Range	100 m to 2 KMs, depends on the following factors:
Over-the-air	AES 128-bit encryption
Weather	Highly sensitive due to rain range conditions. For more information in range, refer
靈敏度	Rain and attenuation table.
Frequency	Power / Magnetic Field Band
c2	57 - 71 40 dBm E.I.R.P., 23 dBm/MHz E.I.R.P. density and maximum transmit power of 27
GHz	dBm at the antenna port/ports.
c3	57-71 55 dBm E.I.R.P., 38 dBm/MHz E.I.R.P. density and transmit antenna gain ≥ 30 dBi. GHz
Site Name	Site Location Radius of exclusion zone from the center of site location
Site 1	07° 23’ 36.6” W, 57° 21’ 3.6” N 6 Km
Site 2	04° 58’ 21” W, 51° 37’ 16.8” N 6 Km
Site 3	00° 36’ 22.8” W, 52° 38’ 1.8” N 6 Km
Where:	Is:
Lfree_space	Free Space Path Loss (dB)
Lexcess	Excess Path Loss (dB)
Lfade	Fade Margin Required (dB)
Lseasonal	Seasonal Fading (dB)
Lcapability	Equipment Capability (dB)
安裝	74
Bracket	Pole diameter ODU Bracket part number variants
V1000 pole mount	40 mm to 77 mm (1.6 inches V1000 Included with V1000 to 3.0 inches)
V1000 wall mount	Wall mount V1000 Included with V1000
V1000 adjustable pole mount	40 mm to 77 mm (1.6 inches V1000 N000900L022A to 3.0 inches)
V3000 precision bracket	25 mm to 77 mm (1.0 inches V3000 C000000L125A to 3.0 inches)
V3000 tilt bracket assembly	40 mm to 77 mm (1.6 inches V3000, N000045L002A
to 3.0 inches)	V5000
with band clamps	inches to 9.0 inches) V5000 party band clamps
V5000 pole mount	25 mm to 77 mm (1.0 inches V5000 C000000L137A to 3.0 inches)
V5000 wall mount	Wall mount V5000 C000000L136A 1. Typical installation 2. ODU interface with LPU on the pole 3. SFP and Aux Ethernet interfaces
Figure 106: AC/DC PSU	Figure 107: Cable joiner Figure 108: DC to (N000000L179B) RJ45 plug, Mini adaptor
Figure 109: AC/DC powering diagram	Figure 110: AC/DC PSU Note Both short and long glands can be used to connect to outdoor PSU. 1. Connect the 56V Gigabit Data + power port to ODU and Gigabit data port to the network equipment.
Figure 111: V1000 power injector	Figure 112: V1000 powering diagram Figure 113: Connecting the V1000 power injector
Optical	Copper
Optical SFP+ module	Copper SFP module 2. Insert the SFP module into the SFP receptacle with the label on the bottom. Figure 119: Inserting the SFP module
Configuring 60 GHz cnWave	112 Internet > Network Connections > Local Area Connection. 2. Select Internet Protocol Version 4 (TCP/IPv4). Figure 130: The Ethernet Properties dialog box 3. Click Properties. 4. Enter an IP address that is valid for the 169.254.X.X/16 network, avoiding 169.254.1.1 (eg: 169.254.1.3).
Element	Description
類型	Displays type of the device. The device types are:
Name	Displays name of the device.
E2E Connection Status	Displays the connection status of the E2E controller.
MAC address	Displays the MAC address of the 60 GHz cnWave device.
Serial Number	Displays the serial number of the 60 GHz cnWave device
Software version	Displays the software version used in 60 GHz cnWave device.
韌體版本	Displays the Firmware version used in 60 GHz cnWave device.
Wireless security	Displays the security type. The types are:
Layer 2 Bridge	Displays bridge status.
System Time	Displays current time. Figure 136: Dashboard - GPS
Fix Type	Fix Type
Satellites tracked	Number of registered satellites
Latitude	Displays latitude of the site
Longitude	Displays longitude of the site
Height	Displays height of the device Figure 137: Dashboard - Sectors
Sync mode	Displays the sync mode of the sectors
Active links	Displays the number of active links in connected sectors
RX Throughput	Displays RX Throughput of the individual sectors
TX Throughput	Displays TX Throughput of the individual sectors Figure 138: Dashboard - Ethernet
Status	Displays the speed of Ethernet ports
RX Packets	Number of packets received
TX Packets	Number of packets transmitted
Elements	Description
Transmit	Transmit power of the radio Power
Adaptive	Select minimum and maximum coding scheme ranging from 2 to 12. Modulation
Sector 1	l Select the frequency channel and polarity.
Sector 1 Link	Golay codes help in avoiding inter-sector interference. In rare scenarios, individual links (s) Golay might require separate Golay codes. In most scenarios, all the links belonging to a sector are configured same Golay code. The controller automatically sets the Golay code. To manually override, select the check box and set the Golay from the drop- down. Override All button helps in setting the sa
Sector 2	Select the frequency channel and polarity.
Sector 2 Link	Golay code. (s) Golay
GPS	If enabled then, the radio uses internal sync rather than the GPS sync. In some scenarios like lab setups, it may be necessary to disable GPS. Caution 60 GHz cnWave V1000 and V3000 devices has only Sector 1. Figure 160: The Antenna section Caution Small dish is supported only for 60 GHz cnWave V3000.
IPv4	Static IPv4 address of the individual node. Node’s GUI /CLI can be opened using
Address	this IP address when directly connected over Ethernet. For Over the air access, L2 Bridge should be enabled. Its predominantly used on PoP nodes with the onboard controller.
Subnet	Subnet mask for the IPv4 address. Mask
Gateway	IPv4 Gateway address. IP Address 2. Under PoP Configuration, select the options for PoP Routing, PoP Interface, and click Generate to generate PoP Interface IP Address.
PoP	PoP nodes connect to the upstream IPv6 router in one of two ways: Routing
接口	when the L2 bridge is enabled.
IPv6	Gateway address. Can be left empty when the L2 bridge is enabled and no IPV6
E2E IPv6 Address	Address of E2E Controller. When using the onboard controller on the same node, can be left empty and GUI automatically fills the POP IPv6 address.
E2E Network Prefix	Seed Prefix in the CIDR format followed by a comma and the prefix length. Should be specified when BGP is used. Otherwise, optional.
IPv6 CPE Interface	IPv6 SLAAC provides IP prefix to downstream CPE devices. Keep it disabled when L2 Bridge is active. 4. Select required BGP configuration. Figure 163: The BGP Configuration section Table 39: Elements in the BGP Configuration section
Local ASN	Local ASN
Neighbour ASN	Upstream router's ASN
Neighbour IPv6	Upstream router's IPv6 address
Specific Network prefixes	Specifically allocated network prefixes to be advertised via BGP 5. Enable the required Ethernet ports. Individual Ethernet ports can be turned off with this configuration.
Layer 2	It has three options: Bridge
CPE	IPv6 SLAAC provides IP prefix to downstream CPE devices. Disable this if the L2 bridge is active. Select the CPE interface:
Aux PoE	Enable PoE out (25 W) on V5000/V3000 aux port. 802.3af and 802.3at compliant devices could be powered up, passive PoE devices cannot be powered up. Note that the aux port cannot power another V5000/V3000.
Relay Port	Specify the Ethernet interfaces on which OpenR is running. It is needed in two cases:
Operation	149 After selecting the software image, the upload status is displayed. Figure 185: The Images page A pop-up message is displayed after the upload.
Link Name	Link name
A-Node	Initiator Node
Z-Node	Responder Node
RSSI	Receiver Signal Strength Indicator
信噪比 SNR	Signal to Noise Ratio
MCS	Modulation Coded Scheme
TX Power Index	Transmitter power index
RX Frames	Receiver frames
RX Errors	Receiver errors
RX PER	Receiver packer error rate
RX Beam Index	Receiver beam index
TX Frames	Transmitter frames
TX Errors	Transmitter errors
TX PER	Transmitter packer error rate
TX Beam Index	Transmitter beam index Figure 192: The Ethernet page
Device Name	Name of the device
RX Bytes	Receiver bytes
TX Bytes	Transmitter bytes
RX Dropped	Receiver dropped
TX Dropped	Transmitter dropped
RX PPS	Receiver Packets Per Second
TX PPS	Transmitter Packets Per Second
Device	Name of the device
MAC	MAC address of the device
Satellites	The number of satellites tracked tracked
MAC Address	MAC address of the device
Sync Mode	l GPS sync: l Entry condition: Valid samples from GPS have been received for a few consecutive seconds (typically 2 seconds).
安全	Security type
Error	Error Association
Channel Last	Channel Last State
MCS Index	Modulation and Coding Scheme (MCS) Index Values can be used to determine the likely data rate of your wireless connection. The MCS value essentially summarizes the number of spatial streams, the modulation type and the coding rate that is possible when connecting your wireless access point.
Packet Error	Packet error ratio. It is the ratio, in percent, of the number of Test Packets not
Ratio	successfully received by the node to the number of Test Packets sent to the node by the test set.
Received	The number of frames received at the node.
Transferred	The number of frames transferred from the node. Figure 196: RSSI graph
Region	Specification
USA	UL 62368-1, UL 60950-22
Canada	CSA C22.2 No.62368-1, CSA C22.2 No. 60950-22
Europe	EN 62368-1, EN 60950-22
International	CB certified IEC 62368-1 Edition 2 IEC 60950 -22
Regulatory Information	170
Europe/International	EN 301 489-1 V2.2.3, EN 301 489-17 V3.2.4
Product	Countries EIRP EIRP Maximum power density Compliance distance (dBm) (W) (W/m2) (m)
Accessories	Radio nodes Cambium Part Number 60 GHz cnWave™ V5000 Distribution Node V5000 C6000500A004A 60 GHz cnWave™ V3000 Client Node radio only V3000 C600500C024A 60 GHz cnWave™ V1000 Client Node with no cord V1000 C600500C14A 60 GHz cnWave™ V1000 with US cord V1000 C600500C001A
Troubleshooting	177 Figure 222: Saving the log files 1. Click Configuration on the left pane, navigate to Network > Basic > Layer 2 Bridge and verify Enable Layer 2 bridge is selected.
User Guides	http://www.cambiumnetworks.com/guides
Technical training	https://learning.cambiumnetworks.com
Support website	https://support.cambiumnetworks.com
Main website	http://www.cambiumnetworks.com
Sales enquiries	solutions@cambiumnetworks.com
Support enquiries	https://support.cambiumnetworks.com Telephone number list http://www.cambiumnetworks.com/contact-us/
Cambium Networks	187

* 規格以原廠最新 Datasheet 為準。

下載完整PDF規格書 →

外形尺寸

118 mm (4.64 in) x 43 mm (1.69 in) x 32.4 mm (1.27 in)｜重量 0.18 Kg (0.39 lbs)｜Unit: mm

網絡 WiFi安裝工程服務

HKEZIT 專營裝WIFI、裝ROUTER、裝FIREWALL工程，60GHZ 由我們供貨、安裝、調試到使用教學一站式完成。無論裝WIFI、裝ROUTER或裝FIREWALL，均由自家工程團隊上門施工，品質有保證。

裝WIFI 裝ROUTER 裝FIREWALL

網絡 WiFi適合邊類專業客戶

60GHZ Cambium 60 GHZ cnWave™亦適合以下專業服務機構使用，保安同合規要求同一般商鋪唔一樣，歡迎查詢度身方案。

心臟科診所

心電圖同貴重心臟監測儀器防盜，診症室私隱合規佈點，配合預約系統。

WhatsApp 查詢 →

脊醫／物理治療中心

治療室私隱同貴重儀器防盜，配合預約系統管理，減少候診糾紛。

WhatsApp 查詢 →

會計師行

審計旺季外勤同事考勤管理、財務資料室保安，同會計師行嘅合規要求相符。

WhatsApp 查詢 →

測量師行／則師樓

現場勘察資料同客戶物業圖則屬機密，辦公室網絡同門禁保安係基本要求。

WhatsApp 查詢 →

建築工程顧問公司

圖則模型檔案室保密，配合工地現場監控延伸管理，項目資料防外洩。

WhatsApp 查詢 →

律師事務所

客戶機密文件與會議記錄保安需求高，門禁分級、CCTV存證、通話錄音缺一不可。

WhatsApp 查詢 →

常見問題

60GHZ 香港哪裡有代理？

HKEZIT 提供原廠行貨連保養，60GHZ 原廠行貨連保養，提供上門安裝、佈線及網絡設定一站式服務，全港 32 區均有服務。

此設備適合什麼工程場景？

詳細規格請參閱上方規格表；我們會按現場點位數量、距離及功率需求設計網絡架構，並提供整體方案報價。

安裝後有問題如何跟進？

原廠行貨保養，工程另設保養期；網絡設備我們會預先設定好即插即用，日後有問題可遠程協助或上門檢查。

60GHZ 定 80211AC 邊個好？

兩者主要規格分別：CABLE, UL POWER SUPPLY CORD SET, INDIA方面，60GHZ 係 V1000, V3000, N000900L012A V5000 V5000，80211AC 係 N000900L012；重量方面，60GHZ 係 0.18 Kg (0.39 lbs)，80211AC 係 0.7 kg (1.5 lbs) without brackets；Temperature方面，60GHZ 係 0°C (32°F) to +50°C (140°F)，80211AC 係 -30°C to +60°C (-22°F to 140°F) PAGE 1-7。實際邊個型號更適合，需視乎現場環境同需求而定，可先比較 80211AC 詳細規格，或直接聯絡我們免費現場評估，由工程師建議最合適方案。