HONEYWELL CSSV1500 防盜報警安裝・保養

Name: HONEYWELL CSSV1500 Issue 4
Brand: Honeywell
SKU: CSSV1500

產品簡介

Honeywell CSSV1500 為Issue 4，HKEZIT 提供原廠行貨連保養、上門安裝、調試及使用教學一站式服務。詳細規格以下方原廠 Datasheet 欄位為準，歡迎聯絡我們查詢 CSSV1500 香港價格連安裝報價。

Characteristic：Symbol Unit Condition
Min.：Typ. Max. Primary current, nominal measuring
IPN：A -1500 — 1500 — range (dc)
Supply voltage：VS V 6 12 18 — Supply voltage hysteresis:
maximum：VUP V — 18.5 — when VC increases

HKEZIT 提供原廠行貨保養。硬件連專業安裝、設定及使用教學一站式報價，無需自行研究安裝與設定。我們同時承接裝ALARM、裝防盜、裝警鐘工程，硬件與工程同一團隊負責。

查詢價格連安裝 →

詳細規格

Characteristic	Symbol Unit Condition
Min.	Typ. Max. Primary current, nominal measuring
IPN	A -1500 — 1500 — range (dc)
Supply voltage	VS V 6 12 18 — Supply voltage hysteresis:
maximum	VUP V — 18.5 — when VC increases
VUP	V — 18.0 — when VC decreases
minimum	VLOW V — 6.4 — when VC increases
VLOW	V — 5.9 — when VC decreases
Current consumption	IC mA 40 — 200 VS = 12 V, T = 25°C temperature range with
Ambient operating temperature	TA °C [°F] -40 [-40] — 85 [185] accuracy guaranteed T = -40°C to 85°C,
High precision channel offset at IP = 0 A	IOS A ±0.1 VS = 9 V to 16 V, ±3 sigma High precision channel total accuracy:
high at IP = 0 A to 20 A	IOS A -0.1 — +0.1 T = -40°C to 85°C,
high at 20 A < IP < 1500 A	XG — — ±0.5% of IP — VS = 9 V to 16 V, ±3 sigma Redundancy channel total accuracy:
low at IP = 0 A to 300 A	IOS A -15 — +15 T = -40°C to 85°C,
low at IP = 300 A to 1500 A	XG — — ±5% of IP — VS = 9 V to 16 V, ±3 sigma CSSV1500 Current Sensors Datasheet \| sps.honeywell.com/ast \| 2 TABLE 3. MECHANICAL SPECIFICATIONS
Housing material	PA66+GF25 (UL 94V - 0) M5, torque = 3,5 N m max. The installation bracket should have a flatness tolerance of ≤0,2 mm. The size tolerances of the
Mounting screws	installation bracket and nut, as well as the use of installation tools and fixtures, have an impact on the maximum installation torque of the product. If there are any relevant design or process changes, it is advisable to implement them after verification.
Mating electrical connector	TE MPN 1473672-1
重量	168 g ±5 g TABLE 4. CERTIFICATIONS
Automotive Safety Integrity Level	ASIL C
Pollution degree	PD2
-1500 -1000	-500 0 500 1000 1500 IP (A) CSSV1500 Series Current Sensors Datasheet \| sps.honeywell.com/ast \| 3 TABLE 5. ORDER GUIDE
Catalog Listing	Description CSSV1500N Series ASIL C current sensors, 1500 A, through-hole mounting with stainless steel CSSV1500N-154 bushing, 500 k baud rate, 3C4 CAN ID CSSV1500N Series ASIL C current sensors, 1500 A, through-hole mounting with stainless steel CSSV1500N-155 bushing, 500 k baud rate, 3C5 CAN ID CSSV1500N Series ASIL C current sensors, 1500 A, through-hole mounting with stainless steel CSSV1500N-
CS	S V 1500 N - 1 5 4 R
Rated	Fixture MCU Baud
類型	Principle Use CAN ID1 Customization
Current	Type Type Rate ASIL C
V Designed for	1500 1500 A Through-hole 1 MCU1 5 500 k 4 3C4 R2
vehicle	mounting with
applications	stainless 5 3C5 steel bushing 6 3C6 Custom CAN IDs are available. Contact Honeywell Customer Service for more information. Customization selection “R” indicates reverse current direction. CSSV1500 Current Sensors Datasheet \| sps.honeywell.com/ast \| 4
Speed	See Figure 2
Protocol	version 2.0A
Oscillator tolerance	0.3125%
Byte order	big endian (Motorola)
StatusOutOf	StatusCurrent
Byte	SequenceCounterIP Error Information
RangeIndication	ValueIndication 0 7 6 5 4 3 2 1 0 1 15 14 13 12 11 10 9 8 2 23 22 21 20 19 18 17 16 3 31 30 29 28 27 26 25 24 4 39 38 37 36 35 34 33 32 5 47 46 45 44 43 42 41 40 6 55 54 53 52 51 50 49 48 7 63 62 61 60 59 58 57 56
Signal Name	Description
SequenceCounterIP	Initial value is 0, plus 1 every frame. Reset to 0 when the counter reaches 14. 01: Power in Under Voltage, 10: Power in Over Voltage, 11: Internal Error,
ErrorInformation	10 state, Current Value Output 0xFFFFFF/0xFFFF 11 state, Output Current value
StatusOutOfRange	0: Normal, 1: Out of Measure Range
StatusCurrentValueInvalid	0: Current Value is valid, 1: Current Value is invalid Unsigned number 24 bits, Unit: mA (offset 0x800000) When out of range occurs, becomes 0xFFFFFF, Ip_oc = 1550 A
-1500 ≤ Ip ≤ +1500	signal = Ip accuracy = Spec
-Ip_oc ≤ Ip < -1500	signal = Ip accuracy = ±2% (for reference)
+1500 < Ip ≤ Ip_oc	signal = Ip accuracy = ±2% (for reference)
Ip < -Ip_oc	signal = 0xFFFFFF accuracy = NA
Ip > Ip_oc	signal = 0xFFFFFF accuracy = NA Unsigned number 16 bits, Unit: A (offset 0x8000) When out of range occurs, becomes 0xFFFF, Ip_oc = 1550 A
Low Precision Current	-Ip_oc ≤ Ip < -1500 signal = Ip accuracy = ±10% (for reference)
Software Build	Software version 8 bit SAE J1850 CRC/AUTOSAR profile 1 DataId = Same as CAN ID; DataIdMode = E2E_P01_DATAID_BOTH CSSV1500 Series Current Sensors Datasheet \| sps.honeywell.com/ast \| 5 73,6 [2.90] 63,5 [2.5] ø24,22 [0.95]
[0.47]	2X ø5,4 [0.21] 69,05 [2.72] [1.26] [1.22] 48,7 SEE DETAIL A
[1.92]	29,8 [1.17] 6,45 [0.25] PINOUT 10,45
Pin	Output [0.41] 1 CAN-L 2 CAN-H 3 GND 4 VS DETAIL A 2D Barcode includes: C S SV15 0 0 N -X X X : C ATALOG LISTING (E X AMPLE ) Y YDDD 0 0 N: SN CODE Y Y: PART PRODUCTION YE AR DDD: DAY OF THE YE AR 0 0 N: NUMBER (IN HE X ADECIMAL) OF DAILY PART PRODUCTION
All other versions	Customized version "R" CSSV1500 Current Sensors Datasheet \| sps.honeywell.com/ast \| 6
Test Name	Standard Procedure According to CISPR 25:2008 Commission
CISPR 25 Conducted RF Emissions - Voltage	CISPR25 Form of Testing According to CISPR 25:2008 Commission
CISPR 25 Conducted RF Emissions - Current	CISPR25 Form of Testing According to CISPR 25:2008 Commission
CISPR 25 Radiated Emissions - ALSE Method	CISPR25 Form of Testing
Transient Conduction Emission	ISO 7637-2 According to ISO 7637-2
Low Frequency Magnetic Field Emission	SAE J551-5 According to SAE J551-5
Bulk Current Injection (BCI) Test	ISO 11452-4 According to ISO 11452-4
Rf Anti-Interference - ALSE Method	ISO 11452-2 According to ISO 11452-2
ISO 7637-3	According to ISO 7637-3
Low Frequency Field Interference	ISO 11452-8 According to ISO 11452-8 Unpowered direct contact discharge: ±15 kV Unpowered air discharge: ±15 kV
Electrostatic Discharge	ISO 10605 Powered-up direct contact discharge: ±8 kV Powered-up air discharge: ±15 kV
Portable Transmitter	ISO 11452-9 According to ISO 11452-9 10 V/m (80 MHz to 1 GHz), 3 V/m (1.4 GHz to
Radio Frequency Electromagnetic Field	IEC 61000-4-3 2 GHz), 1 V/m (2.0 GHz to 2.7 GHz)
Radio Frequency Continuous Conducted	IEC 61000-4-6 0.15 MHz to 80 MHz, 3 V 80% AM (1 kHz)
Radio Frequency Magnetic Field	IEC 61000-4-8 30 A/M CSSV1500 Series Current Sensors Datasheet \| sps.honeywell.com/ast \| 7 TABLE 10. ENVIRONMENTAL TEST SPECIFICATIONS
Low Temperature Storage	ISO16750-4 and VS nom. 48 hr, -40°C power off. Performance test before and after test at 25°C and
High Temperature Storage	ISO16750-4 VS nom. 120 cycles: one cycle contains -40°C (120 min soak) and 85°C (120 min
Thermal Cycle Test	ISO16750-4 soak). Transition time = 120 min. Performance test before and after test at 25°C and VS nom.
High Temperature and	1000 hr, 85°C, 85% humidity, power on with 100 A primary current. ISO16750-4
Humidity Endurance	Performance after test, from −40°C to 85°C, notify XG ≤1 % 5 Hz to 2000 Hz, 20 hr/axis, three axes with −40°C/85°C temperature
Vibration	IEC60068-2-64 cycle during test. Product power on with 100 A primary current. Performance test before and after test at 25°C and VS nom. 500 m/s, 2,20 each direction (60 total), half sine pulse. Product power
Mechanical Shock	ISO16750-3 on with 100 A primary current. Performance test before and after test at 25°C and VS nom. With final packaging, drop in direction at one corner, three edge, four ISTA-1A or GB/T
Package Drop	face > total nine drops, one m on concrete floor. Performance test before 4857.5 and after test at 25°C and VS nom. First fall of each DUT at a different dimensional axis. Second fall with the given DUT at the same dimensional axis but on the opposite side of the
Handling Drop	ISO 16750-3 housing, from 1 m on concrete floor. Performance test before and after test at 25°C and VS nom. Waterproof and Dust (and
ISO20653	IP category: 40 other Solid Intrusion) CSSV1500 Current Sensors Datasheet \| sps.honeywell.com/ast \| 8 TABLE 11. ELECTRICAL TEST SPECIFICATIONS1
Long Time Overvoltage Test	ISO 16750-2 Power supply at 18 V for 60 min. Test voltage UC max 16 V for 12 V systems; ac voltage (sinusoidal):
Superimposed Alternating Voltage	ISO 16750-2 Severity 2, UPP = 4 V Slow Decrease Fast Increase of
ISO 16750-2-4.5	According to ISO 16750-2-4.5 testing standard and Fig Supply Voltage
Reset Behavior at Voltage Drop	ISO16750-2-4.6.2.2 See Fig. 6
Transient Overvoltage Test	ISO16750-2 Power supply at 24 V for 10 min.
Momentary Drop in Supply Voltage	ISO 16750-2-4.6.1 U C min to 4.5 V. See Fig. 4
Load Dump	ISO 16750-2-4.6.4 Pulse described in Table 6. See Fig. 9
Reverse Voltage Test	ISO16750-2-4.7 Power supply at -24 V for 10 min. Connect sensor to 12 V power supply and power on the sensor.
Single Line Open Circuit Tests	ISO16750-2-4.9 Disconnect Us, GND, CAN-H, and CAN-L in sequence. Each open circuit time: 60 ±1 s Connect sensor to 12 V power supply and power on the sensor.
Connector Open Circuit Tests	ISO16750-2 Disconnect connector. Each open circuit time: 10 ±1 s
Insulation Resistance Test	ISO 16750-2-4.12 500 Vdc for 60 s; Resistance criteria: >500 MOhm Test Voltage: 5000 Vdc and ac. Frequency: dc and 50~60 Hz. Test
dc and ac Voltage Insulation Test	— Duration: 60 s See the applicable standard for all table and figure references. CSSV1500 Series Current Sensors Datasheet \| sps.honeywell.com/ast \| 9
NOTICE	m WARNING
PRELIMINARY	Honeywell warrants goods of its PERSONAL INJURY manufacture as being free of defective
DOCUMENTATION	DO NOT USE these products as safety
materials and faulty workmanship	or emergency stop devices or in any The information contained in this
during the applicable warranty period.	other application where failure of the document is preliminary and for
reference only. Preliminary means	Honeywell’s standard product warranty product could result in personal injury.
that the product described has not	applies unless agreed to otherwise by Failure to comply with these
been or is currently being formally	Honeywell in writing; please refer to instructions could result in death or
tested. Specifications are subject to	your order acknowledgment or consult serious injury. change without notice. Reliance on the your local sales office for specific information contained herein is at the warranty details. If warranted goods reader’s own risk. are returned to Honeywell during the m WARNING
period of coverage, Honeywell will	MISUSE OF
repair or replace, at its option, without	DOCUMENTATION
charge those items that Honeywell,	• The information presented in this
in its sole discretion, finds defective.	product sheet is for reference only. Do not use this document as The foregoing is buyer’s sole remedy a product installation guide.
and is in lieu of all other warranties,	• Complete installation, operation,
expressed or implied, including those	and maintenance information
of merchantability and fitness for a	is provided in the instructions
particular purpose. In no event shall	supplied with each product.
Honeywell be liable for consequential,	Failure to comply with these
special, or indirect damages.	instructions could result in death or serious injury. While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer’s sole responsibility to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is
For more information	believed to be accurate and reliable
Honeywell Sensing & Safety	as of this writing. However, Honeywell
Technologies services its customers	assumes no responsibility for its use.
USA/Canada	+1 302 613 4491
Latin America	+1 305 805 8188
Europe	+44 1344 238258
Japan	+81 (0) 3-6730-7152
Singapore	+65 6355 2828
Greater China	+86 4006396841 006007-4-EN \| 4 \| 01/24
www.honeywell.com	© 2024 Honeywell International Inc. All rights reserved.