| • Saves the cost of two | and secondary • Base network • Built-In Power Supply • QOS: Quality of Service |
|---|
| dedicated phone lines. | telephone ports. connection (LAN or module: On board diagnostics via |
|---|
| WAN), DSL modem or | charging circuit design AlarmNet conveys vital |
|---|
| • Dual path | • Operates over the cable modem. accommodates back- communicator |
|---|
| communications. Can | following up battery. Includes information including |
|---|
| communicate to | communication • Data transmits over primary power and when message was |
|---|
| central station using | protocols: HSPA+ (4G), standard contact-ID battery supervision. received, signal |
|---|
| Internet or cellular | HSPA (HSDPA & protocol but is secured strength, and message |
|---|
| technology. | HSUPA) (3G), EDGE with the industry's • Diagnostic LEDs: path used. (2G GPRS) (2G). advanced encryption Signal strength and |
|---|
| • Requires no change to | standard (AES 256 bit). status indicators. • 7720P Hand-held |
|---|
| the existing Fire Alarm | • Works over any type of programmer for easy |
|---|
| Control Panel | customer provided • Supports both dynamic • Reliable connection: IP setup. |
|---|
| configuration. The | Ethernet 10/100. (DHCP) or Public and and GSM connection |
|---|
| IPGSM-4GC connects | Private Static IP tested every day. |
|---|
| directly to the primary | addressing. |
|---|
| Operation | Panel Capabilities |
|---|
| the Internet (primary). | of redundant hardware servers, hot back-up databases and generators with battery back-up at all locations to |
|---|
| Easy to Program | ensure continuity of service. Signals from Alarm-Net |
|---|
| The IPGSM-4GC communicator can be pre- | are transmitted to the central station's receivers using |
|---|
| a PC at the remote site for programming. | and within 20 feet of the fire panel. The wiring must be routed through conduit. |
|---|
| are: | • IPGSM-4GC, and all equipment used for the IP connection (such as the router, hub, modem, etc.) |
|---|
| monitoring station. | switched branch circuit, and be provided with appropriate standby power. |
|---|
| your monitoring station. | • IPGSM-4GC must use the 7AH battery (not supplied) to provide 24-hour backup capability. |
|---|
| ELECTRICAL | installed in an environment with a normal room Ademco® and AlarmNet® are |
|---|
| temperature of 15 - 27°C/60 - 80°F. | registered trademarks of |
|---|
| Transformer: 1451-UL9. | Honeywell International Inc. |
|---|
| Primary: 120 VAC, 60 Hz, 850mA. | PRODUCT LINE INFORMATION This document is not intended |
|---|
| Secondary: 18VDC, 72 VA. | IPGSM-4GC: (For Canada only): Internet and Digital to be used for installation |
|---|
| 電池 | Cellular Fire Alarm Communicator Panel. Includes red purposes. We try to keep our One 12 V 7.0 AH lead-acid battery (not supplied). cabinet with key, wall outlet box, Dialer Capture Module, product information up-to- iGSM Communications Module, antenna & mounting date and accurate. We cannot |
|---|
| Battery charging current minimum 1 Amp. | cover all specific applications adapter, PowerBoost1 power supply, LED display board, Battery discharge current standby 230mA, active transformer, manual, & required screws, cables, etc. or anticipate all requirements. 950mA. All specifications are subject to |
|---|
| HFS-659EN: Telco line fault monitor. | change without notice. IPGSM-4GC cabinet holds one 7.0 AH battery. |
|---|
| CABINET | GSM-ANT3DB: 3db gain external/remote antenna. |
|---|
| Color: Red. | WA7626-CA: SNA to N Adapter. |
|---|
| SHIPPING | 7720P: IPGSM-4GC hand held programmer. HPTCOVER: Plug in transformer box for IPGSM |
|---|
| Weight: 5.3 lbs. (6.94 kg). | communicator. AGENCY LISTINGS AND APPROVALS The listings and approvals below apply to the basic Consult factory for latest listing status. DH-60771 | D | 06/17 |
|---|
| www.honeywell.com | ©2017 Honeywell International Inc. |
|---|
